Speed Bleeder 10mm Speed Bleeders, Set (4) M10x1.0mm SB1010
Brand: Speed BleederManufacturer’s Part Number: SB1010Size: 10×1.0mmQuantity (2 packs of 2) 10mm x 34.44mm lengthAllows brake bleeding to be easily done by only one personSimply turn screw 1/3 turn out and pump brake pedal to bleed the brakesEasy installationInstallation Note: The bleeder screws only require a small amount of torque to be tighten sufficiently. Over tightening can result in a broken bleeder screw or stripped caliper threads. The factory torque specification is only 5.8 ft/lbs.
Speed Bleeder 10mm Speed Bleeders, (Single) M10x1.0 SB1010
Brand: Speed BleederManufacturer’s Part Number: SB1010Size: 10×1.0mmQuantity: (1 pack) Manufacturer’s Description:Features of SPEED BLEEDER brand checkvalve• Stainless steel spring• Stainless steel ball• Brass retainer• The threads are roll formed. This process results in a stronger and smoother thread than one that is cut.• The chamber for the ball and spring is precision reamed and the seat for the stainless steel ball is machined to exacting tolerances.• Zinc chromate plating withstands a 30 hour salt spray. Other plating with higher salt spray results is also available.• Patented thread sealing system seals the threads when the bleeding operation is performed, preventing air from being sucked back into the system.• The pre-applied thread sealant also displaces air and moisture during thread engagement preventing rust…which usually results in rounded off corners on the hex or busted off bleeder screws making it necessary to replace the caliper or brake cylinder. The application of thread sealant thus makes it easy to loosen or remove the bleeder screw at any time.Benefits of SPEED BLEEDER brand checkvalve• Simple to use• Saves time and money• Requires only one person to do• Perfect for racing where brake fluid is changed frequently• A must for the do-it-yourselfer• Available for automobiles, motorcycles and trucks and any vehicle with hydraulic brakesThe old manual wayBleeding brakes used to be a difficult thing to do in the past. It generally required two people to bleed brakes. You had to have one person pump the brake pedal while you had the mechanic open and close the bleeder screw. You had to coordinate the openings and closings with the pumper. If you didn’t coordinate the timing correctly you could end up with more air in the system than when you started.Alternative waysBleeding brakes can be done a number of ways:• You can use a pressure bleeder that attaches to your master cylinder and pressurizes the system. You open each bleeder screw individually to bleed your brakes. It costs about $300.00. It works very well, but who wants to invest $300.00 to bleed one or two vehicles.• A vacuum bleeder is another way to bleed brakes. It attaches to your bleeder screw and sucks the fluid from the master cylinder, thus bleeding your brakes. If not used correctly, it can let air into your brake system. It costs from $30.00-$100.00.The NEW and IMPROVED way!Introducing SPEED BLEEDER brand check valve, the Speed Bleeder screw with the built-in check valve. It is truly a one-person device. Once installed, it becomes a permanent part of the brake system. When it is time to bleed your brakes, you loosen the Speed Bleeder screw a 1/4 turn and pump your brake pedal. When the pedal is depressed the pressure generated opens the check valve letting air and brake fluid out of the end of the Speed Bleeder screw. When you release the pedal and it returns to the up position, the check valve closes and prevents any air from reentering the system through the Speed Bleeder screw. When bubble free fluid is evident you close the Speed Bleeder screw. In the closed position it works just like your stock bleeder screw and prevents any brake fluid from leaking out. It generally takes about 5 pumps to purge each caliper or wheel cylinder. That is all there is to bleeding your brakes. If at a later date you need to bleed your brakes, the patented thread sealing system makes it easy to open the Speed Bleeder screw to perform the bleeding operation. It is made of quality materials and it is economical.
Speed Bleeder (10mm, Stainless Steel, Set/4) M10x1.0mm SB1010-SS
Brand: Speed BleederManufacturer’s Part Number: SB1010-SSSize: M10 x 1.0mmPrimary Material: 303 Stainless SteelPack Quantity: 4Condition: New ProductKit Contents: 4x M10x1.0mm Stainless Steel Speed Bleeder Screws 4x Rubber dust cap10mm x 34.44mm lengthAllows brake bleeding to be easily done by only one personSimply turn screw 1/3 turn out and pump brake pedal to bleed the brakesEasy installationInstallation Note: The bleeder screws only require a small amount of torque to be tighten sufficiently. Over tightening can result in a broken bleeder screw or stripped caliper threads. The factory torque specification is only 5.8 ft/lbs. Manufacturer’s Description:Features of SPEED BLEEDER brand checkvalve• Stainless steel spring• Stainless steel ball• Brass retainer• The threads are roll formed. This process results in a stronger and smoother thread than one that is cut.• The chamber for the ball and spring is precision reamed and the seat for the stainless steel ball is machined to exacting tolerances.• Zinc chromate plating withstands a 30 hour salt spray. Other plating with higher salt spray results is also available.• Patented thread sealing system seals the threads when the bleeding operation is performed, preventing air from being sucked back into the system.• The pre-applied thread sealant also displaces air and moisture during thread engagement preventing rust…which usually results in rounded off corners on the hex or busted off bleeder screws making it necessary to replace the caliper or brake cylinder. The application of thread sealant thus makes it easy to loosen or remove the bleeder screw at any time.Benefits of SPEED BLEEDER brand checkvalve• Simple to use• Saves time and money• Requires only one person to do• Perfect for racing where brake fluid is changed frequently• A must for the do-it-yourselfer• Available for automobiles, motorcycles and trucks and any vehicle with hydraulic brakesThe old manual wayBleeding brakes used to be a difficult thing to do in the past. It generally required two people to bleed brakes. You had to have one person pump the brake pedal while you had the mechanic open and close the bleeder screw. You had to coordinate the openings and closings with the pumper. If you didn’t coordinate the timing correctly you could end up with more air in the system than when you started.Alternative waysBleeding brakes can be done a number of ways:• You can use a pressure bleeder that attaches to your master cylinder and pressurizes the system. You open each bleeder screw individually to bleed your brakes. It costs about $300.00. It works very well, but who wants to invest $300.00 to bleed one or two vehicles.• A vacuum bleeder is another way to bleed brakes. It attaches to your bleeder screw and sucks the fluid from the master cylinder, thus bleeding your brakes. If not used correctly, it can let air into your brake system. It costs from $30.00-$100.00.The NEW and IMPROVED way!Introducing SPEED BLEEDER brand check valve, the Speed Bleeder screw with the built-in check valve. It is truly a one-person device. Once installed, it becomes a permanent part of the brake system. When it is time to bleed your brakes, you loosen the Speed Bleeder screw a 1/4 turn and pump your brake pedal. When the pedal is depressed the pressure generated opens the check valve letting air and brake fluid out of the end of the Speed Bleeder screw. When you release the pedal and it returns to the up position, the check valve closes and prevents any air from reentering the system through the Speed Bleeder screw. When bubble free fluid is evident you close the Speed Bleeder screw. In the closed position it works just like your stock bleeder screw and prevents any brake fluid from leaking out. It generally takes about 5 pumps to purge each caliper or wheel cylinder. That is all there is to bleeding your brakes. If at a later date you need to bleed your brakes, the patented thread sealing system makes it easy to open the Speed Bleeder screw to perform the bleeding operation. It is made of quality materials and it is economical.
Speed Bleeder 10mm Speed Bleeders, Set (2) M10x1.0 SB1010
Brand: Speed BleederManufacturer’s Part Number: SB1010Size: 10×1.0mmQuantity (1 pack of 2) Manufacturer’s Description:Features of SPEED BLEEDER brand checkvalve• Stainless steel spring• Stainless steel ball• Brass retainer• The threads are roll formed. This process results in a stronger and smoother thread than one that is cut.• The chamber for the ball and spring is precision reamed and the seat for the stainless steel ball is machined to exacting tolerances.• Zinc chromate plating withstands a 30 hour salt spray. Other plating with higher salt spray results is also available.• Patented thread sealing system seals the threads when the bleeding operation is performed, preventing air from being sucked back into the system.• The pre-applied thread sealant also displaces air and moisture during thread engagement preventing rust…which usually results in rounded off corners on the hex or busted off bleeder screws making it necessary to replace the caliper or brake cylinder. The application of thread sealant thus makes it easy to loosen or remove the bleeder screw at any time.Benefits of SPEED BLEEDER brand checkvalve• Simple to use• Saves time and money• Requires only one person to do• Perfect for racing where brake fluid is changed frequently• A must for the do-it-yourselfer• Available for automobiles, motorcycles and trucks and any vehicle with hydraulic brakesThe old manual wayBleeding brakes used to be a difficult thing to do in the past. It generally required two people to bleed brakes. You had to have one person pump the brake pedal while you had the mechanic open and close the bleeder screw. You had to coordinate the openings and closings with the pumper. If you didn’t coordinate the timing correctly you could end up with more air in the system than when you started.Alternative waysBleeding brakes can be done a number of ways:• You can use a pressure bleeder that attaches to your master cylinder and pressurizes the system. You open each bleeder screw individually to bleed your brakes. It costs about $300.00. It works very well, but who wants to invest $300.00 to bleed one or two vehicles.• A vacuum bleeder is another way to bleed brakes. It attaches to your bleeder screw and sucks the fluid from the master cylinder, thus bleeding your brakes. If not used correctly, it can let air into your brake system. It costs from $30.00-$100.00.The NEW and IMPROVED way!Introducing SPEED BLEEDER brand check valve, the Speed Bleeder screw with the built-in check valve. It is truly a one-person device. Once installed, it becomes a permanent part of the brake system. When it is time to bleed your brakes, you loosen the Speed Bleeder screw a 1/4 turn and pump your brake pedal. When the pedal is depressed the pressure generated opens the check valve letting air and brake fluid out of the end of the Speed Bleeder screw. When you release the pedal and it returns to the up position, the check valve closes and prevents any air from reentering the system through the Speed Bleeder screw. When bubble free fluid is evident you close the Speed Bleeder screw. In the closed position it works just like your stock bleeder screw and prevents any brake fluid from leaking out. It generally takes about 5 pumps to purge each caliper or wheel cylinder. That is all there is to bleeding your brakes. If at a later date you need to bleed your brakes, the patented thread sealing system makes it easy to open the Speed Bleeder screw to perform the bleeding operation. It is made of quality materials and it is economical.
1L Air Brake Bleeder Kit Pneumatic Clutch Vacuum Hydraulic Fluid Fill Bottle Set
DescriptionFeatures: Brake fluid bleeder works with your air compressor to quickly assist in your brake bleeding!Flush and refill the entire brake system by yourself with this brake fluid bleeder.34 oz Waster Brake Fluid Tank24 oz New Fluid tank that inserts into your master cylinder with provided adaptersAir requirement: 90 to 120 PSI, Air inlet: 1/4- 18 NPTProduct Description:Pneumatic Brake Fluid Bleeder w/ 4 master cylinder adapters 90 – 120 PSI Brake fluid bleeder works with your air compressor to quickly assist in your brake bleeding!The simplicity of this tool allows brake bleeding to get done by one person easily.Flush and refill the entire brake system by yourself with this brake fluid bleeder.?Convenient one-person operation?Flush and refill entire brake system 34 oz Waster Brake Fluid Tank 24 oz New Fluid tank that inserts into your master cylinder with provided adaptersMaster Cylinder Reservoir Adapters : 1.25 INCHES.-1.60 INCHES (32 to 41mm) 1.10 INCHES.-1.45 INCHES (28 to 37mm) 0.95 INCHES.-1.25 INCHES (24 to 32mm) 0.80 INCHES.-1.20 INCHES (21 to 30mm)Air requirement: 90 to 120 PSI, Air inlet: 1/4- 18 NPT ****DOES NOT HAVE INSTRUCTION & MANUAL •Our products are professional auto tools. You should only purchase the tools if you are familiar with how to fix cars.•Proper use of the tools are important to prevent from any unnecessary injuries.•Heavy duty moulded storage case (may get dent or crack during shipping)•Case color may vary. Paymentent Payment methods accepted : Paypal only.Payment must be received within 7 business days of auction closing.We ship to your Paypal address. Please make sure your Paypal address is correct before you pay.Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched. Shipping & HandlingThe items you ordered will be shipped out in 1-2 business day from Los Angeles，CA or New York. And you will receive it in one week. Return & WarrantyIf the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement.But the items must be back in factory condition. Please contact us and double check the return address before you return it.If is item is defective in 1 months, you can return it to us. We will send you a new replacement after receiving the defective item.Feedback We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us.We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.It is impossible to address issues if we do not know about them! About usWe care about our valued buyers, if you have any questions, our Customer Service staffs will be very glad to help you.We try our best to reply to your emails as soon as possible, however, due to high volume of daily incoming emails and time zonedifference, we may not be able to reply your emails immediately. Please allow 24 business hours for us to response.
Speed Bleeder Brake Bleeder Screws 10mm Short, Stainless Steel, Set/8 SB1010S-SS
FITMENTS:2004-2007 STi2008-2014 STi2015-2017 STi2018-2021 STi Brand: Speed BleederManufacturer’s Part Number: SB1010S-SSSize: 10×1.0mmQTY: 4 packs of 2 Allows brake bleeding to be easily done by only one personSimply turn screw 1/3 turn out and pump brake pedal to bleed the brakesEasy installationApplication Note: Each Brembo calipers utilizes two bleeder screws. Installation Note: The bleeder screws only require a small amount of torque to be tighten sufficiently. Over tightening can result in a broken bleeder screw or stripped caliper threads. The factory torque specification is only 5.8 ft/lbs.
Brake / Clutch Bleeding ABS System Hydrauic Fluid Bleed Tool 2.5L 70Psi Bleeder
Description One-man brake and clutch bleeding the professional way. Bleeding requires no external power source – simply fill and pump. Reservoir holds 2.5ltr of hydraulic fluid – flush the entire system with one fill without the risk of running the reservoir dry. Pressure range makes unit suitable for use with ABS systems. Fitted with 42mm cap with 90 degrees angled connector which is suitable for most European models. For other applications order optional Brake Reservoir Cap 42mm Straight Connector =========================================================================== ****DOES NOT HAVE INSTRUCTION & MANUAL •Our products are professional auto tools. You should only purchase the tools if you are familiar with how to fix cars. •Proper use of the tools are important to prevent from any unnecessary injuries. •Heavy duty moulded storage case (may get dent or crack during shipping) •Case color may vary.PaymentPayment must be received within 7 business days of auction closing. We ship to your Paypal address. Please make sure your Paypal address is correct before you pay. Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched. Shipping & Handling The items you ordered will be shipped out in 1-3 business day from Rancho Cucamonga,California, And you will receive it in about one week .It will be extended under special circumstances Return & Warranty If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 1 months, you can return it to us. We will send you a new replacement after receiving the defective item. Feedback We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.It is impossible to address issues if we do not know about them! About usWe care about our valued buyers, if you have any questions, our Customer Service staffs will be very glad to help you. We try our best to reply to your emails as soon as possible, however, due to high volume of daily incoming emails and time zone difference, we may not be able to reply your emails immediately. Please allow 24 business hours for us to response.